bs=4M
+ sync
+```
- 4. Use the board's power switch to turn on the board.
+### Booting the Board
+
+Follow these steps to boot the board:
- After a few seconds, you will see the AGL splash screen on the display and you
- will be able to log in at the console's terminal or using the graphic screen.
+1. Use the board's power switch to turn off the board.
+
+2. Insert the MicroSD card into the board.
-## 6. Setting Up the Serial Console
+3. Verify that you have plugged in the following:
+
+ * An external monitor into the board's HDMI port
- Setting up the Serial Console involves the following:
+ * An input device (e.g. keyboard, mouse, touchscreen, and so forth) into the board's USB ports.
+
+4. Use the board's power switch to turn on the board.
- * Installing a serial client on your build host
- * Connecting your build host to your Renesas board's serial port
- * Powering on the board to get a shell at the console
- * Configuring U-Boot parameters
- * Logging into the console
- * Determining the board's IP address
+After a few seconds, you will see the AGL splash screen on the display and you
+will be able to log in at the console's terminal or using the graphic screen.
+
+## 8. Setting Up the Serial Console
+
+Setting up the Serial Console involves the following:
+
+* Installing a serial client on your build host
+* Connecting your build host to your Renesas board's serial port
+* Powering on the board to get a shell at the console
+* Configuring U-Boot parameters
+* Logging into the console
+* Determining the board's IP address
- Brief about each process :
+### Installing a Serial Client on Your Build Host
- 1. Installing a Serial Client on Your Build Host
+You need to install a serial client on your build host.
+Some examples are
+[GNU Screen](https://en.wikipedia.org/wiki/GNU_Screen),
+[picocom](https://linux.die.net/man/8/picocom),
+and
+[Minicom](https://en.wikipedia.org/wiki/Minicom).
- You need to install a serial client on your build host.
- Some examples are [GNU Screen](https://en.wikipedia.org/wiki/GNU_Screen), [picocom](https://linux.die.net/man/8/picocom), and [Minicom](https://en.wikipedia.org/wiki/Minicom). Of these three, "picocom" has less dependencies and is therefore considered the "lightest" solution.
+Of these three, "picocom" has less dependencies and is therefore
+considered the "lightest" solution.
- 2. Connecting Your Build Host to Your Renesas Board's Serial Port
+### Connecting Your Build Host to Your Renesas Board's Serial Port
- You need to physically connect your build host to the Renesas board using
- a USB cable from the host to the serial CP2102 USP port (i.e. Micro USB-A port)
- on the Renesas board.
+You need to physically connect your build host to the Renesas board using
+a USB cable from the host to the serial CP2102 USP port (i.e. Micro USB-A port)
+on the Renesas board.
+
+
Once you connect the board, determine the device created for the serial link.
- Use the `dmesg` command on your build host.
-
- ```sh
- dmesg | tail 9
- [2097783.287091] usb 2-1.5.3: new full-speed USB device number 24 using ehci-pci
- [2097783.385857] usb 2-1.5.3: New USB device found, idVendor=0403, idProduct=6001
- [2097783.385862] usb 2-1.5.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
- [2097783.385864] usb 2-1.5.3: Product: FT232R USB UART
- [2097783.385866] usb 2-1.5.3: Manufacturer: FTDI
- [2097783.385867] usb 2-1.5.3: SerialNumber: AK04WWCE
- [2097783.388288] ftdi_sio 2-1.5.3:1.0: FTDI USB Serial Device converter detected
- [2097783.388330] usb 2-1.5.3: Detected FT232RL
- [2097783.388658] usb 2-1.5.3: FTDI USB Serial Device converter now attached to ttyUSB0
- ```
-
- The device created is usually `/dev/ttyUSB0`.
- However, the number might vary depending on other USB serial ports connected to the host.
-
- To use the link, you need to launch the client.
- Here are three commands, which vary based on the serial client, that show
- how to launch the client:
-
- ```sh
- picocom -b 115200 /dev/ttyUSB0
- ```
-
- or
-
- ```sh
- minicom -b 115200 -D /dev/ttyUSB0
- ```
-
- or
-
- ```sh
- screen /dev/ttyUSB0 115200
- ```
-
-
- 3. Powering on the Board to Get a Shell at the Console
-
- Both the Pro and Premier kits (e.g.
- [m3ulcb](https://elinux.org/R-Car/Boards/M3SK) and
- [h3ulcb](https://elinux.org/R-Car/Boards/H3SK#Hardware)) have nine
- switches (SW1 through SW9).
- To power on the board, "short-press" SW8, which is the power switch.
-
- Following, is console output for the power on process for each kit:
-
+ Use the ``dmesg`` command on your build host.
+ Here is an example:
+
+
+
+dmesg | tail 9
+[2097783.287091] usb 2-1.5.3: new full-speed USB device number 24 using ehci-pci
+[2097783.385857] usb 2-1.5.3: New USB device found, idVendor=0403, idProduct=6001
+[2097783.385862] usb 2-1.5.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
+[2097783.385864] usb 2-1.5.3: Product: FT232R USB UART
+[2097783.385866] usb 2-1.5.3: Manufacturer: FTDI
+[2097783.385867] usb 2-1.5.3: SerialNumber: AK04WWCE
+[2097783.388288] ftdi_sio 2-1.5.3:1.0: FTDI USB Serial Device converter detected
+[2097783.388330] usb 2-1.5.3: Detected FT232RL
+[2097783.388658] usb 2-1.5.3: FTDI USB Serial Device converter now attached to ttyUSB0
+
+
+
+
+The device created is usually "/dev/ttyUSB0".
+However, the number might vary depending on other USB serial ports connected to the host.
+
+To use the link, you need to launch the client.
+Here are three commands, which vary based on the serial client, that show
+how to launch the client:
+
+
+```sh
+$ picocom -b 115200 /dev/ttyUSB0
+```
+
+or
+
+```sh
+$ minicom -b 115200 -D /dev/ttyUSB0
+```
+
+or
+
+```sh
+$ screen /dev/ttyUSB0 115200
+```
+
+### Powering on the Board to Get a Shell at the Console
+
+Both the Pro and Premier kits (e.g.
+[m3ulcb](https://elinux.org/R-Car/Boards/M3SK) and
+[h3ulcb](https://elinux.org/R-Car/Boards/H3SK#Hardware)) have nine
+switches (SW1 through SW9).
+To power on the board, "short-press" SW8, which is the power switch.
+
+Following, is console output for the power on process for each kit:
+
+
+
h3ulcb:
-
- ```sh
- NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.7
- NOTICE: BL2: PRR is R-Car H3 ES1.1
- NOTICE: BL2: LCM state is CM
- NOTICE: BL2: DDR1600(rev.0.15)
- NOTICE: BL2: DRAM Split is 4ch
- NOTICE: BL2: QoS is Gfx Oriented(rev.0.30)
- NOTICE: BL2: AVS setting succeeded. DVFS_SetVID=0x52
- NOTICE: BL2: Lossy Decomp areas
- NOTICE: Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
- NOTICE: Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
- NOTICE: Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
- NOTICE: BL2: v1.1(release):41099f4
- NOTICE: BL2: Built : 19:20:52, Jun 9 2016
- NOTICE: BL2: Normal boot
- NOTICE: BL2: dst=0xe63150c8 src=0x8180000 len=36(0x24)
- NOTICE: BL2: dst=0x43f00000 src=0x8180400 len=3072(0xc00)
- NOTICE: BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
- NOTICE: BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)
- NOTICE: BL2: dst=0x49000000 src=0x8640000 len=1048576(0x100000)
-
-
- U-Boot 2015.04 (Jun 09 2016 - 19:21:52)
-
- CPU: Renesas Electronics R8A7795 rev 1.1
- Board: H3ULCB
- I2C: ready
- DRAM: 3.9 GiB
- MMC: sh-sdhi: 0, sh-sdhi: 1
- In: serial
- Out: serial
- Err: serial
- Net: Board Net Initialization Failed
- No ethernet found.
- Hit any key to stop autoboot: 0
- ```
-
-
+
+
+
+
+NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.7
+NOTICE: BL2: PRR is R-Car H3 ES1.1
+NOTICE: BL2: LCM state is CM
+NOTICE: BL2: DDR1600(rev.0.15)
+NOTICE: BL2: DRAM Split is 4ch
+NOTICE: BL2: QoS is Gfx Oriented(rev.0.30)
+NOTICE: BL2: AVS setting succeeded. DVFS_SetVID=0x52
+NOTICE: BL2: Lossy Decomp areas
+NOTICE: Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
+NOTICE: Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
+NOTICE: Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
+NOTICE: BL2: v1.1(release):41099f4
+NOTICE: BL2: Built : 19:20:52, Jun 9 2016
+NOTICE: BL2: Normal boot
+NOTICE: BL2: dst=0xe63150c8 src=0x8180000 len=36(0x24)
+NOTICE: BL2: dst=0x43f00000 src=0x8180400 len=3072(0xc00)
+NOTICE: BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
+NOTICE: BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)
+NOTICE: BL2: dst=0x49000000 src=0x8640000 len=1048576(0x100000)
+
+
+U-Boot 2015.04 (Jun 09 2016 - 19:21:52)
+
+CPU: Renesas Electronics R8A7795 rev 1.1
+Board: H3ULCB
+I2C: ready
+DRAM: 3.9 GiB
+MMC: sh-sdhi: 0, sh-sdhi: 1
+In: serial
+Out: serial
+Err: serial
+Net: Board Net Initialization Failed
+No ethernet found.
+Hit any key to stop autoboot: 0
+=>
+
+
+
+
+
+
m3ulcb:
-
- ```sh
- NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.14
- NOTICE: BL2: PRR is R-Car M3 Ver1.0
- NOTICE: BL2: Board is Starter Kit Rev1.0
- NOTICE: BL2: Boot device is HyperFlash(80MHz)
- NOTICE: BL2: LCM state is CM
- NOTICE: BL2: AVS setting succeeded. DVFS_SetVID=0x52
- NOTICE: BL2: DDR1600(rev.0.22)NOTICE: [COLD_BOOT]NOTICE: ..0
- NOTICE: BL2: DRAM Split is 2ch
- NOTICE: BL2: QoS is default setting(rev.0.17)
- NOTICE: BL2: Lossy Decomp areas
- NOTICE: Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
- NOTICE: Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
- NOTICE: Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
- NOTICE: BL2: v1.3(release):4eef9a2
- NOTICE: BL2: Built : 00:25:19, Aug 25 2017
- NOTICE: BL2: Normal boot
- NOTICE: BL2: dst=0xe631e188 src=0x8180000 len=512(0x200)
- NOTICE: BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
- NOTICE: BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
- NOTICE: BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)
- NOTICE: BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)
-
-
- U-Boot 2015.04-dirty (Aug 25 2017 - 10:55:49)
-
- CPU: Renesas Electronics R8A7796 rev 1.0
- Board: M3ULCB
- I2C: ready
- DRAM: 1.9 GiB
- MMC: sh-sdhi: 0, sh-sdhi: 1
- In: serial
- Out: serial
- Err: serial
- Net: ravb
- Hit any key to stop autoboot: 0
- ```
-
-## 7. Setting-up U-boot
-
- **Configuring U-Boot Parameters**
-
- Follow these steps to configure the board to use the MicroSD card as the
- boot device and also to set the screen resolution:
-
- 1. As the board is powering up, press any key to stop the autoboot process.
- You need to press a key quickly as you have just a few seconds in which to
- press a key.
-
- 2. Once the autoboot process is interrupted, use the board's serial console to
- enter `printenv` to check if you have correct parameters for booting your board:
-
- Here is an example using the **h3ulcb** board:
-
- ```sh
- $ printenv
- baudrate=115200
- bootargs=console=ttySC0,115200 root=/dev/mmcblk1p1 rootwait ro rootfstype=ext4
- bootcmd=run load_ker; run load_dtb; booti 0x48080000 - 0x48000000
- bootdelay=3
- fdt_high=0xffffffffffffffff
- initrd_high=0xffffffffffffffff
- load_dtb=ext4load mmc 0:1 0x48000000 /boot/r8a7795-h3ulcb.dtb
- load_ker=ext4load mmc 0:1 0x48080000 /boot/Image
- stderr=serial
- stdin=serial
- stdout=serial
- ver=U-Boot 2015.04 (Jun 09 2016 - 19:21:52)
-
- Environment size: 648/131068 bytes
+
+
+
+NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.14
+NOTICE: BL2: PRR is R-Car M3 Ver1.0
+NOTICE: BL2: Board is Starter Kit Rev1.0
+NOTICE: BL2: Boot device is HyperFlash(80MHz)
+NOTICE: BL2: LCM state is CM
+NOTICE: BL2: AVS setting succeeded. DVFS_SetVID=0x52
+NOTICE: BL2: DDR1600(rev.0.22)NOTICE: [COLD_BOOT]NOTICE: ..0
+NOTICE: BL2: DRAM Split is 2ch
+NOTICE: BL2: QoS is default setting(rev.0.17)
+NOTICE: BL2: Lossy Decomp areas
+NOTICE: Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
+NOTICE: Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
+NOTICE: Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
+NOTICE: BL2: v1.3(release):4eef9a2
+NOTICE: BL2: Built : 00:25:19, Aug 25 2017
+NOTICE: BL2: Normal boot
+NOTICE: BL2: dst=0xe631e188 src=0x8180000 len=512(0x200)
+NOTICE: BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
+NOTICE: BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
+NOTICE: BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)
+NOTICE: BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)
+
+
+U-Boot 2015.04-dirty (Aug 25 2017 - 10:55:49)
+
+CPU: Renesas Electronics R8A7796 rev 1.0
+Board: M3ULCB
+I2C: ready
+DRAM: 1.9 GiB
+MMC: sh-sdhi: 0, sh-sdhi: 1
+In: serial
+Out: serial
+Err: serial
+Net: ravb
+Hit any key to stop autoboot: 0
+=>
+
+
+
+
+## 9. Setting-up U-boot
+### Configuring U-Boot Parameters
+
+Follow these steps to configure the board to use the MicroSD card as the
+boot device and also to set the screen resolution:
+
+1. As the board is powering up, press any key to stop the autoboot process.
+ You need to press a key quickly as you have just a few seconds in which to
+ press a key.
+
+2. Once the autoboot process is interrupted, use the board's serial console to
+ enter printenv to check if you have correct parameters for booting your board:
+
+
+ Here is an example using the h3ulcb board:
+
+
+
+
+ => printenv
+ baudrate=115200
+ bootargs=console=ttySC0,115200 root=/dev/mmcblk1p1 rootwait ro rootfstype=ext4
+ bootcmd=run load_ker; run load_dtb; booti 0x48080000 - 0x48000000
+ bootdelay=3
+ fdt_high=0xffffffffffffffff
+ initrd_high=0xffffffffffffffff
+ load_dtb=ext4load mmc 0:1 0x48000000 /boot/r8a7795-h3ulcb.dtb
+ load_ker=ext4load mmc 0:1 0x48080000 /boot/Image
+ stderr=serial
+ stdin=serial
+ stdout=serial
+ ver=U-Boot 2015.04 (Jun 09 2016 - 19:21:52)
+
+ Environment size: 648/131068 bytes
+
+
+
+
+
+ Here is a second example using the m3ulcb board:
+
+
+
+ => printenv
+ baudrate=115200
+ bootargs=console=ttySC0,115200 root=/dev/mmcblk1p1 rootwait ro rootfstype=ext4
+ bootcmd=run load_ker; run load_dtb; booti 0x48080000 - 0x48000000
+ bootdelay=3
+ fdt_high=0xffffffffffffffff
+ filesize=cdeb
+ initrd_high=0xffffffffffffffff
+ load_dtb=ext4load mmc 0:1 0x48000000 /boot/r8a7796-m3ulcb.dtb
+ load_ker=ext4load mmc 0:1 0x48080000 /boot/Image
+ stderr=serial
+ stdin=serial
+ stdout=serial
+ ver=U-Boot 2015.04 (Nov 30 2016 - 18:25:18)
+
+ Environment size: 557/131068 bytes
+
+
+
+
+ 3. To boot your board using the MicroSD card, be sure your environment is set up
+ as follows:
+
+ ```shell
+ setenv bootargs console=ttySC0,115200 ignore_loglevel vmalloc=384M video=HDMI-A-1:1920x1080-32@60 root=/dev/mmcblk1p1 rw rootfstype=ext4 rootwait rootdelay=2
+ setenv bootcmd run load_ker\; run load_dtb\; booti 0x48080000 - 0x48000000
+ setenv load_ker ext4load mmc 0:1 0x48080000 /boot/Image
```
- Here is a second example using the **m3ulcb** board:
-
- ```sh
- $ printenv
- baudrate=115200
- bootargs=console=ttySC0,115200 root=/dev/mmcblk1p1 rootwait ro rootfstype=ext4
- bootcmd=run load_ker; run load_dtb; booti 0x48080000 - 0x48000000
- bootdelay=3
- fdt_high=0xffffffffffffffff
- filesize=cdeb
- initrd_high=0xffffffffffffffff
- load_dtb=ext4load mmc 0:1 0x48000000 /boot/r8a7796-m3ulcb.dtb
- load_ker=ext4load mmc 0:1 0x48080000 /boot/Image
- stderr=serial
- stdin=serial
- stdout=serial
- ver=U-Boot 2015.04 (Nov 30 2016 - 18:25:18)
-
- Environment size: 557/131068 bytes
- ```
-
- 3. Loading dtb :
+ 4. Loading dtb :
**NOTE** : Refer [here](https://elinux.org/R-Car/Boards/Yocto-Gen3-CommonFAQ/Which_dtb_file_is_required_to_boot_linux_on_the_R-Car_Starter_Kit_board_%3F) for more information.
@@ -472,172 +748,198 @@ Follow these steps to download the drivers you need:
* **M3SK with a Kingfisher board** : `$ setenv load_dtb ext4load mmc 0:1 0x48000000 /boot/r8a7796-m3ulcb-kf.dtb`
- 4. Set Correct Environment :
-
- Be sure your environment is set up as follows:
+ 5. Save the boot environment:
- ```sh
- $ setenv bootargs console=ttySC0,115200 ignore_loglevel vmalloc=384M video=HDMI-A-1:1920x1080-32@60 root=/dev/mmcblk1p1 rw rootfstype=ext4 rootwait rootdelay=2
- $ setenv bootcmd run load_ker\; run load_dtb\; booti 0x48080000 - 0x48000000
- $ setenv load_ker ext4load mmc 0:1 0x48080000 /boot/Image
- ```
+ ```shell
+ saveenv
+ ```
- 5. Save the boot environment: `$ saveenv`
+ 6. Boot the board:
+ ```sh
+ run bootcmd
+ ```
- 6. Boot the board: `$ run bootcmd`
-## 8. Troubleshooting
- * **Logging Into the Console**
+## 10. Troubleshooting
+### Logging Into the Console
- Once the board boots, you should see the
- [Wayland display](https://en.wikipedia.org/wiki/Wayland_(display_server_protocol))
- on the external monitor.
- A login prompt should appear as follows depending on your board:
+Once the board boots, you should see the
+[Wayland display](https://en.wikipedia.org/wiki/Wayland_(display_server_protocol))
+on the external monitor.
+A login prompt should appear as follows depending on your board:
- **h3ulcb**:
- ```sh
- Automotive Grade Linux ${AGL_VERSION} h3ulcb ttySC0
+**h3ulcb**:
- h3ulcb login: root
- ```
+```sh
+Automotive Grade Linux ${AGL_VERSION} h3ulcb ttySC0
- **m3ulcb**:
- ```sh
- Automotive Grade Linux ${AGL_VERSION} m3ulcb ttySC0
+h3ulcb login: root
+```
- m3ulcb login: root
- ```
+**m3ulcb**:
- At the prompt, login by using `root` as the login.
- The password is "empty" so you should not be prompted for the password.
+```sh
+Automotive Grade Linux ${AGL_VERSION} m3ulcb ttySC0
- * **Determining the Board's IP Address**
+m3ulcb login: root
+```
- If your board is connected to a local network using Ethernet and
- if a DHCP server is able to distribute IP addresses,
- you can determine the board's IP address and log in using `ssh`.
+At the prompt, login by using `root` as the login.
+The password is "empty" so you should not be prompted for the password.
- Here is an example for the m3ulcb board:
+### Determining the Board's IP Address
- ```sh
- m3ulcb login: root
- root@m3ulcb:~# ip -4 a
- 1: lo: mtu 65536 qdisc noqueue state UNKNOWN group default
- inet 127.0.0.1/8 scope host lo
- valid_lft forever preferred_lft forever
- 3: eth0: mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
- inet 10.0.0.27/24 brd 10.0.0.255 scope global eth0
- valid_lft forever preferred_lft forever
- ```
+If your board is connected to a local network using Ethernet and
+if a DHCP server is able to distribute IP addresses,
+you can determine the board's IP address and log in using `ssh`.
+
+
+ Here is an example for the m3ulcb board:
+
+
+
+ m3ulcb login: root
+ Last login: Tue Dec 6 09:55:15 UTC 2016 on tty2
+ root@m3ulcb:~# ip -4 a
+ 1: lo: mtu 65536 qdisc noqueue state UNKNOWN group default
+ inet 127.0.0.1/8 scope host lo
+ valid_lft forever preferred_lft forever
+ 3: eth0: mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
+ inet 10.0.0.27/24 brd 10.0.0.255 scope global eth0
+ valid_lft forever preferred_lft forever
+ root@m3ulcb:~#
+
+
+
+
+
+
In the previous example, IP address is 10.0.0.27.
Once you know the address, you can use `ssh` to login.
+ Following is an example that shows logging into SSH and then
+ displaying the contents of the `/etc/os-release` file:
+
+
+
+ $ ssh root@10.0.0.27
+ Last login: Tue Dec 6 10:01:11 2016 from 10.0.0.13
+ root@m3ulcb:~# cat /etc/os-release
+ ID="poky-agl"
+ NAME="Automotive Grade Linux"
+ VERSION="3.0.0+snapshot-20161202 (chinook)"
+ VERSION_ID="3.0.0-snapshot-20161202"
+ PRETTY_NAME="Automotive Grade Linux 3.0.0+snapshot-20161202 (chinook)"
+
+
+
- ```sh
- $ ssh root@10.0.0.27
- ```
-
-## 9. Supplementary Information
-
- * R-Car Generation 3 Information
-
- Refer to the following for more information from [eLinux website](https://elinux.org/R-Car).
+**NOTE:** More generics troubleshooting can be found here : [Generic issues](../troubleshooting.html)
- * Proprietary libraries for meta-rcar-gen3
+## 11. Supplementary Information
- The meta-rcar-gen3 layer of meta-renesas is supported Graphic GLES(GSX)
- libraries, proprietary library of multimedia, and ICCOM software.
+* R-Car Generation 3 Information
- 1. Build with Renesas multimedia libraries
+Refer to the following for more information from [eLinux website](https://elinux.org/R-Car).
- Multimedia portions depend on GLES portions.
+* Proprietary libraries for meta-rcar-gen3
- * A. Configuration for Multimedia features
+The meta-rcar-gen3 layer of meta-renesas is supported Graphic GLES(GSX)
+libraries, proprietary library of multimedia, and ICCOM software.
+1. Build with Renesas multimedia libraries
- * Please copy proprietary libraries to the directory of recipes.
+Multimedia portions depend on GLES portions.
- * Please set local.conf the following.
- **Enable multimedia features. This provides package group of plug-ins of the GStreamer, multimedia libraries and kernel drivers.**
+* A. Configuration for Multimedia features
- ```sh
- MACHINE_FEATURES_append = " multimedia"
- ```
+ * Please copy proprietary libraries to the directory of recipes.
- * B. Configuration for optional codecs and middleware
+ * Please set local.conf the following.
+ **Enable multimedia features. This provides package group of plug-ins of the GStreamer, multimedia libraries and kernel drivers.**
- * Please copy proprietary libraries to the directory of recipes.
-
- * Add features to DISTRO_FEATURES_append to local.conf
-
- **Additional configuration in OMX module**
-
- ```sh
- " h263dec_lib" - for OMX Media Component H263 Decoder Library
- " h264dec_lib" - for OMX Media Component H264 Decoder Library
- " h264enc_lib" - for OMX Media Component H.264 Encoder Library
- " h265dec_lib" - for OMX Media Component H265 Decoder Library
- " mpeg2dec_lib" - for OMX Media Component MPEG2 Decoder Library
- " mpeg4dec_lib" - for OMX Media Component MPEG4 Decoder Library
- " vc1dec_lib" - for OMX Media Component VC-1 Decoder Library
- " divxdec_lib" - for OMX Media Component DivX Decoder Library
- " rvdec_lib" - for OMX Media Component RealVideo Decoder Library
- " alacdec_lib" - for OMX Media Component ALAC Decoder Library
- " flacdec_lib" - for OMX Media Component FLAC Decoder Library
- " aaclcdec_lib" - for OMX Media Component AAC-LC Decoder Library
- " aaclcdec_mdw" - for AAC-LC 2ch Decoder Middleware for Linux
- " aacpv2dec_lib" - for OMX Media Component aacPlus V2 Decoder Library
- " aacpv2dec_mdw" - for aacPlus V2 Decoder Middleware for Linux
- " mp3dec_lib" - for OMX Media Component MP3 Decoder Library
- " mp3dec_mdw" - for MP3 Decoder Middleware for Linux
- " wmadec_lib" - for OMX Media Component WMA Standard Decoder Library
- " wmadec_mdw" - for WMA Standard Decoder Middleware for Linux
- " dddec_lib" - for OMX Media Component Dolby(R) Digital Decoder Library
- " dddec_mdw" - for Dolby(R) Digital Decoder Middleware for Linux
- " aaclcenc_lib" - for OMX Media Component AAC-LC Encoder Library
- " vp8dec_lib" - for OMX Media Component VP8 Decoder Library for Linux
- " vp8enc_lib" - for OMX Media Component VP8 Encoder Library for Linux
- " vp9dec_lib" - for OMX Media Component VP9 Decoder Library for Linux
- " aaclcenc_mdw" - for AAC-LC Encoder Middleware for Linux
- " cmsbcm" - for CMS Basic Color Management Middleware for Linux
- " cmsblc" - for CMS CMM3 Backlight Control Middleware for Linux
- " cmsdgc" - for CMS VSP2 Dynamic Gamma Correction Middleware for Linux
- " dtv" - for ISDB-T DTV Software Package for Linux
- " dvd" - for DVD Core-Middleware for Linux
- " adsp" - for ADSP driver, ADSP interface and ADSP framework for Linux
- " avb" - for AVB Software Package for Linux
- ```
-
- Ex:
-
- ```sh
- DISTRO_FEATURES_append = " h264dec_lib h265dec_lib mpeg2dec_lib aaclcdec_lib aaclcdec_mdw"
- ```
+ ```sh
+ MACHINE_FEATURES_append = " multimedia"
+ ```
- * C. Configuration for test packages
+* B. Configuration for optional codecs and middleware
+
+ * Please copy proprietary libraries to the directory of recipes.
+
+ * Add features to DISTRO_FEATURES_append to local.conf
+
+
+
+ **Additional configuration in OMX module**
+
+
+
+ " h263dec_lib" - for OMX Media Component H263 Decoder Library
+ " h264dec_lib" - for OMX Media Component H264 Decoder Library
+ " h264enc_lib" - for OMX Media Component H.264 Encoder Library
+ " h265dec_lib" - for OMX Media Component H265 Decoder Library
+ " mpeg2dec_lib" - for OMX Media Component MPEG2 Decoder Library
+ " mpeg4dec_lib" - for OMX Media Component MPEG4 Decoder Library
+ " vc1dec_lib" - for OMX Media Component VC-1 Decoder Library
+ " divxdec_lib" - for OMX Media Component DivX Decoder Library
+ " rvdec_lib" - for OMX Media Component RealVideo Decoder Library
+ " alacdec_lib" - for OMX Media Component ALAC Decoder Library
+ " flacdec_lib" - for OMX Media Component FLAC Decoder Library
+ " aaclcdec_lib" - for OMX Media Component AAC-LC Decoder Library
+ " aaclcdec_mdw" - for AAC-LC 2ch Decoder Middleware for Linux
+ " aacpv2dec_lib" - for OMX Media Component aacPlus V2 Decoder Library
+ " aacpv2dec_mdw" - for aacPlus V2 Decoder Middleware for Linux
+ " mp3dec_lib" - for OMX Media Component MP3 Decoder Library
+ " mp3dec_mdw" - for MP3 Decoder Middleware for Linux
+ " wmadec_lib" - for OMX Media Component WMA Standard Decoder Library
+ " wmadec_mdw" - for WMA Standard Decoder Middleware for Linux
+ " dddec_lib" - for OMX Media Component Dolby(R) Digital Decoder Library
+ " dddec_mdw" - for Dolby(R) Digital Decoder Middleware for Linux
+ " aaclcenc_lib" - for OMX Media Component AAC-LC Encoder Library
+ " vp8dec_lib" - for OMX Media Component VP8 Decoder Library for Linux
+ " vp8enc_lib" - for OMX Media Component VP8 Encoder Library for Linux
+ " vp9dec_lib" - for OMX Media Component VP9 Decoder Library for Linux
+ " aaclcenc_mdw" - for AAC-LC Encoder Middleware for Linux
+ " cmsbcm" - for CMS Basic Color Management Middleware for Linux
+ " cmsblc" - for CMS CMM3 Backlight Control Middleware for Linux
+ " cmsdgc" - for CMS VSP2 Dynamic Gamma Correction Middleware for Linux
+ " dtv" - for ISDB-T DTV Software Package for Linux
+ " dvd" - for DVD Core-Middleware for Linux
+ " adsp" - for ADSP driver, ADSP interface and ADSP framework for Linux
+ " avb" - for AVB Software Package for Linux
+
+
+
+
+
+ Ex:
- Must ensure that Multimedia features have been enabled.
- (Please refer to III/A to enable Multimedia.)
+ ```sh
+ DISTRO_FEATURES_append = " h264dec_lib h265dec_lib mpeg2dec_lib aaclcdec_lib aaclcdec_mdw"
+ ```
- * Please add feature to DISTRO_FEATURES_append to local.conf.
+* C. Configuration for test packages
- **Configuration for multimedia test package**
- ```sh
- DISTRO_FEATURES_append = "mm-test"
- ```
+ Must ensure that Multimedia features have been enabled.
+ (Please refer to III/A to enable Multimedia.)
- 2. Enable Linux ICCOM driver and Linux ICCOM library
+ * Please add feature to DISTRO_FEATURES_append to local.conf.
+ **Configuration for multimedia test package**
+ ```sh
+ DISTRO_FEATURES_append = "mm-test"
+ ```
- For Linux ICCOM driver and Linux ICCOM library
+2. Enable Linux ICCOM driver and Linux ICCOM library
- * Please copy proprietary libraries to the directory of recipes.
- * Please set local.conf the following.
+ For Linux ICCOM driver and Linux ICCOM library
- ```sh
- DISTRO_FEATURES_append = "iccom"
- ```
+ * Please copy proprietary libraries to the directory of recipes.
+ * Please set local.conf the following.
+ ```sh
+ DISTRO_FEATURES_append = "iccom"
+ ```