-You can find this package in your build environment, using docker SDK recommended setup the file is `/xdt/build/tmp/deploy/rpm/<your-target-arch>/`.
-
-After a successful bitbake build and using Renesas RCar Gen2, Porter, you have to copy the file if your board is connected to your network and you know its IP address:
-
-```bash
-$ scp /xdt/build/tmp/deploy/rpm/cortex15hf_neon/libafbwsc-dev-1.0-r0.cortexa15hf_neon.rpm root@<target_IP>:~
-```
-
-Else, you have to copy into the SDcard with the AGL image installed on it.
-
-From the docker image copy RPM to the shared directory between docker image and your host:
-
-```bash
-$ cp /xdt/build/tmp/deploy/rpm/cortex15hf_neon/libafbwsc-dev-1.0-r0.cortexa15hf_neon.rpm ~/share
-```
-
-Then plugin you SDcard in your Linux host \(Windows can't read ext4 filesystem AGL runs on\) and copy RPM file on it.
-
-From your host, identify SDcard block device node here it is **sdc** with the correct capacity automounted by the desktop manager:
-
-```bash
-$ lsblk
-loop1 7:1 0 2G 0 loop
-└─docker-253:0-3146365-pool 253:3 0 100G 0 dm
- └─docker-253:0-3146365-e9f80849a2681e18549d3a4238cbf031e44052e36cd88a0abf041804b799b61c
- 253:4 0 10G 0 dm /var/lib/docker/devicemapper/mnt/e9f80849a2681e18549d3a4238cbf031e44052e36cd88a0abf041804b799b61c
-sdb 8:16 0 238.5G 0 disk
-├─sdb2 8:18 0 238G 0 part
-│ └─agl 253:1 0 238G 0 lvm /home/claneys/Workspace/agl-docker
-└─sdb1 8:17 0 500M 0 part /boot
-sr0 11:0 1 1024M 0 rom
-loop0 7:0 0 100G 0 loop
-└─docker-253:0-3146365-pool 253:3 0 100G 0 dm
- └─docker-253:0-3146365-e9f80849a2681e18549d3a4238cbf031e44052e36cd88a0abf041804b799b61c
- 253:4 0 10G 0 dm /var/lib/docker/devicemapper/mnt/e9f80849a2681e18549d3a4238cbf031e44052e36cd88a0abf041804b799b61c
-sdc 8:32 1 14.9G 0 disk
-└─sdc1 8:33 1 2G 0 part /run/media/claneys/97f418a5-612f-44e9-b968-a19505695151
-sda 8:0 0 931.5G 0 disk
-├─sda2 8:2 0 500G 0 part
-│ ├─home 253:2 0 150G 0 lvm /home
-│ └─root 253:0 0 50G 0 lvm /
-└─sda1 8:1 0 16G 0 part [SWAP]
-```
-
-Copy, still from your host:
-
-> **CAUTION:** Make sure to sync IO with sync command before unplug your SDcard. It could be corrupted if removed before all pending IO aren't done.